香港2019年六开彩资料精选

欢迎进入慈溪市海升橡胶制品有限公司官网 Bookmark | Message | Sitemap | Contact Haisheng Welcome to the official website of Cixi Haisheng Rubber Products Co., Ltd.

National Consulting Hotline 400-0590-280

Popular keywords: rubber waterproof ring silicone o-ring rubber o-ring nitrile rubber lighter o-ring

o型橡胶密封圈
香港2019年六开彩资料精选 » Haisheng official website information center » FAQ » What are the main reasons for seal failure

What are the main reasons for seal failure

返回列表 Source: Cixi Haisheng Rubber Products Co., Ltd. Date2018-12-03 15:07 Browse: -

Some customers bought seals and looked at the better quality seals, but lost the seal effect. What caused it?

: There are three main reasons for seal failure :

1.The sealing surface is opened

85%的密封失效不是因磨损造成,而是在磨损前就已泄漏了。 When repairing mechanical seals, 85% of seal failures are not caused by wear, but they leak before they wear.

“砂轮”会损坏硬环表面。 When the sealing surface is opened, the solid particles in the medium enter the sealing surface under the effect of liquid pressure. After the sealing surface is closed, these solid particles are embedded in the surface of the soft ring (usually the right ink ring), which actually becomes a " "Grinding wheels" can damage hard ring surfaces.

Because the moving ring or rubber ring is fastened to the shaft (shaft sleeve), when the shaft moves in series, the moving ring cannot fit in time, and the sealing surface is opened, and the hysteresis of the sealing surface is closed, so that solid particles enter the sealing surface. .

At the same time, there are solid particles between the shaft (shaft sleeve) and the sliding parts, which affect the sliding of the rubber ring or the moving ring (relative to the dynamic seal point, common failure). In addition, the medium will also generate crystals in the friction parts of the rubber ring and the shaft (shaft sleeve), and solid substances will also be stored in the spring, which will open the sealing surface.

过热 2. Overheating

Because the sealing surface will generate heat, the temperature of the rubber ring should be lower than the design specification. 216℃,丁晴橡胶的使用温度为162℃,虽然它们都能承受较高的温度,但因密封面产生的热较高,所以橡胶圈有继续硫化的危险,最终失去弹性而泄漏。 The operating temperature of fluororubber and polytetrafluoroethylene is 216 ° C, and the operating temperature of nitrile rubber is 162 ° C. Although they can withstand higher temperatures, the heat generated by the sealing surface is higher, so the rubber ring continues to vulcanize. The danger of eventually losing elasticity and leaking. (The cold zone is considered to be cold and brittle.) The heat will cause the medium to crystallize between the sealing surfaces, such as carbon, causing the sliding parts to be stuck and the sealing surfaces to be condensed. And some polymers are coked due to overheating, some fluids lose their lubrication due to overheating and even flash fire.

In addition to overheating, it can change the condition of the medium and increase its corrosion rate. Causes the deformation of metal parts, cracks on the alloy surface, and cracks in some coatings. The design should select a balanced mechanical seal to reduce the specific pressure and prevent overheating.

超差 3 , out of tolerance

Correct assembly tolerances are necessary for the installation of mechanical seals. The shaft (sleeve) must have a suitable surface roughness and correct dimensions, but manufacturers rarely provide tolerance data, which are critical for installation. of. The dimensional accuracy and form and position tolerances of mechanical seals must meet the requirements of the drawings. Tolerances will cause seals to fail prematurely.

Therefore, these three main factors determine whether the seal will fail. We must also pay attention to our design and installation. 0.01mm,欢迎咨询。 Our Haisheng Rubber rmhym.com has a professional engineer team to design rubber seals for you. The minimum tolerance can reach 0.01mm. Welcome to consult.

Recommended reading

    [Label this article]:

    [Responsible editor]: Cixi Haisheng Rubber Products Co., Ltd. All rights reserved: http://rmhym.com/

    Latest News

    海升橡胶带您了解氟橡胶密封圈的优势 1 Haisheng Rubber takes you to understand the advantages of fluoro rubber seals

    海升橡胶带您了解全氟O型圈的安装注意事项 2Haisheng rubber takes you to understand the installation precautions of perfluoro O-rings

    海升橡胶带您了解氟橡胶密封圈的功能和特性 3 Haisheng Rubber takes you to understand the functions and characteristics of fluoro rubber seals

    海升橡胶带您了解密封圈发生泄漏的因素 4Haisheng rubber takes you to understand the causes of leaks in seals

    海升橡胶带您了解垫片适应的环境 5 Haisheng rubber takes you to understand the environment that the gasket adapts to

    海升橡胶带您了解橡胶制品发白的原因 6 Haisheng Rubber takes you to understand the cause of whitening of rubber products

    海升橡胶带您认识密封圈具有的性能 7 Haisheng rubber takes you to know the performance of the sealing ring

    海升橡胶带您了解怎样选择适合自己的O型圈 8 Haisheng rubber takes you to know how to choose the O-ring that suits you

    海升橡胶带您了解氟硅橡胶O型圈的应用领域 9 Haisheng Rubber takes you to understand the application fields of fluorosilicone O-rings

    海升橡胶带您了解橡胶防水密封圈 10 Haisheng rubber take you to know the rubber waterproof seal

    National Service Hotline 400-0590-280